Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
What're your thoughts on How to Install a Bathtub?
Installing a bath tub isn't exactly brain surgery, but it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately challenging task. If the old tub is easily available, the task can relocate immediately; if you need to open a wall surface to remove the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the brand-new one. Make sure you have actually qualified on your own for the task as well as are comfortable attempting it. Instead of employing a professional to take control of a halfway-completed project, it is far better to consider employing one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This post will aid you set up a new bathtub in your bathroom if you have already gotten a brand-new bathtub and also do not need to transform the arrangement of your previous water supply pipes.
Your devices and also product checklist need to consist of the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any water staying in the system. The process of getting rid of the existing taps can be rather troublesome because of the restricted accessibility that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. When the supply pipes have actually been gotten rid of, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Before carrying on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Making use of both wooden boards under its feet, position the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the level checks out degree.
To mount taps, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipe by making a compression join; then do the very same for the other faucet.
Switch on the water supply and examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise check the overflow outlet and the regular outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the tub has actually been used at the very least when as this will settle it right into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washers remain in location between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet adapters. The former type ought to be connected to the tap ends first, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture a stiff seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, causing difficulties with moisture and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can split fairly early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our piece about Installing A Bathtub. Thank you so much for taking time to browse our article post. Are you aware of someone else who is serious about the niche? Feel free to promote it. Thank you so much for your time invested reading it.
Browse Website Report this page